cypress公司的EZ-PD™ CCG2是具有最新的USB Type-C和PD标准的USB Type-C控制器,为无源电缆,有源电缆和电源附件提供完整的USB Type-C和USB PD端口控制解决方案.器件采用M0S8技术,集成了32位48MHz ARM® Cortex®-M0处理器和32KB闪存,完整的Type-C收发器以及Type-C端电阻RP, RD和 RA主要用在USB Type-C EMCA电缆,电源附件,上行方向端口和下行方向端口.本文介绍了EZ-PD™ CCG2主要特性,逻辑框图,系统框图和多种应用框图,以及CCG2 24W电原适配器(PA)评估板主要指标,电路图,材料清单.
EZ-PD™ CCG2 is a USB Type-C controller that complies with the latest USB Type-C and PD standards. EZ-PD CCG2 provides a complete USB Type-C and USB Power Delivery port control solution for passive cables, active cables, and powered accessories. It can also be used in many upstream and downstream facing port applications. EZ-PD CCG2 uses Cypress’s proprietary M0S8 technology with a 32-bit, 48-MHz ARM® Cortex®-M0 processor with 32-KB flash and integrates a complete Type-C Transceiver including the Type-C termination resistors RP, RD and RA.
EZ-PD™ CCG2主要特性:
32-bit MCU Subsystem
■ 48-MHz ARM Cortex-M0 CPU
■ 32-KB Flash
■ 4-KB SRAM
■ In-system reprogrammable
Integrated Digital Blocks
■ Integrated timers and counters to meet response timesrequired by the USB-PD protocol
■ Run-time reconfigurable serial communication block (SCB)with reconfigurable I2C, SPI, or UART functionality
Clocks and Oscillators
■ Integrated oscillator eliminating the need for external clock
Type-C Support
■ Integrated transceiver (baseband PHY)
■ Integrated UFP (RD), EMCA (RA) termination resistors, andcurrent sources for DFP (RP)
■ Supports one USB Type-C port
Low-Power Operation
■ 2.7-V to 5.5-V operation
■ Two independent VCONN rails with integrated isolationbetween the two
■ Independent supply voltage pin for GPIO that allows 1.71-V to5.5-V signaling on the I/Os
■ Reset: 1.0 μA, Deep Sleep: 2.5 μA, Sleep: 2.0 mA
System-Level ESD on CC and VCONN Pins
■ ± 8-kV Contact Discharge and ±15-kV Air Gap Discharge basedon IEC61000-4-2 level 4C
Packages
■ 1.63 mm × 2.03 mm, 20-ball wafer-level CSP (WLCSP) with0.4-mm ball pitch
■ 2.5 mm × 3.5 mm × 0.6 mm 14-pin DFN
■ 4.0 mm × 4.0 mm, 0.55 mm 24-pin QFN
■ Supports industrial (-40℃ to +85℃) and extended industrial(-40 ℃ to +105 ℃) temperature ranges
Applications
■ USB Type-C EMCA cables
■ USB Type-C powered accessories
■ USB Type-C upstream facing ports
■ USB Type-C downstream facing ports
图1.EZ-PD™ CCG2逻辑框图
图2.EZ-PD™ CCG2框图
图3.USB-PD子系统框图
图4.EZ-PD™ CCG2无源EMCA应用框图:每电缆单个EZ-PD CCG2
图5.EZ-PD™ CCG2无源EMCA应用框图:每插座单个EZ-PD CCG2
图6.EZ-PD™ CCG2上行方向端口(UFP)应用― 带有Type-C 型端口的平板电脑
图7.EZ-PD™ CCG2双功能端口(DRP)应用框图
图8.EZ-PD™ CCG2下行方向端口(DFP)应用框图
图9.USB Type-C和HDMI/DVI/VGA Dongle应用框图
图10.USB Type-C和显示器端口应用框图
图11. 坞站/监视器中CCG2应用框图
CCG2 24W电原适配器(PA)评估板
The CCG2 24W Power Adapter (PA) Board is receptacle based Type-C power adapter which supports outputs of 5V@3A, 9V@2.7A and 12V@2A. The major components on the board are Cypress’s EZ-PD CCG2 (CYPD2134-24LQXIT) controller and Dialog Semiconductor’s iW1782-00 AC-DC controller and iW671-00 Sync Rectifier.
图12.CCG2 24W电源适配器(PA)评估板外形图
图13.CCG2 24W电源适配器(PA)评估板背面元件图
The CCG2 device on the board handles USB Type-C interface and PD 2.0 whereas AC-DC power conversion, Over Current Protection (OCP) and Over Voltage Protection (OVP) are handled by Dialog Semiconductor’s iW1782-00 AC-DC controller, which supports universal AC input supply. The board hardware design files (schematic, bill of materials and board files) are readily available below for customers to reduce the design cycle.
CCG2 24W电源适配器(PA)评估板主要指标:
图14.CCG2 24W电源适配器(PA)评估板电路图(1)
图15.CCG2 24W电源适配器(PA)评估板电路图(2)
图16.CCG2 24W电源适配器(PA)评估板电路图(3)
CCG2 24W电源适配器(PA)评估板材料清单:
详情请见:
http://www.cypress.com/file/140151/download