NXP公司的KW40Z/30Z/20Z是超低功耗高度集成系统级芯品(SoC),集成了工作频率2.36 GHz到2.48 GHz的无线收发器,支持FSK/GFSK和O-QPSK调制器;以及ARM Cortex-M0+CPU, 160 KB闪存和20KB SRAM,BLE链接层硬件,802.15.4包处理器硬件和外设,支持蓝牙低功耗(BLE)或IEEE尺度802.15.4 RF毗连,主要用在手持保健设备,可穿着运动和健美设备,AV遥控,盘算机键盘和鼠标,游戏控制器,接图控制,安全系统,智能能源和家庭局域网.本京电港论坛文章先容了KW40Z主要特点,框架图,以及低功耗蓝牙(BLE)心率监测仪参考方案主要特点,框架图,应用框架图,软件架构图和电路原理图纸.
The KW40Z/30Z/20Z (called KW40Z throughout this document) is an ultra low-power,highly integrated single-chip device that enables Bluetooth low energy (BLE) or IEEE Standard 802.15.4 RF connectivity for portable, extremely low-power embeddedsystems. Applications include portable health care devices, wearable sports and fitnessdevices, AV remote controls, computer keyboards and mice, gaming controllers, accesscontrol, security systems, smart energy and home area networks.
The KW40Z SoC integrates a radio transceiver operating in the 2.36 GHz to 2.48 GHz range supporting a range of FSK/GFSK and O-QPSK modulations, an ARM Cortex-M0+CPU, 160 KB Flash and 20 KB SRAM, BLE Link Layer hardware, 802.15.4 packet processor hardware and peripherals optimized to meet the requirements of the target applications.
The KW40Z SoC’s radio frequency transceiver is compliant with Bluetooth version 4.1 for Low Energy (aka Bluetooth Smart), and the IEEE standard 802.15.4-2011 using OQPSKin the 2.4 GHz ISM band.
The KW40Z SoC can be used in applications as a "BlackBox" modem by simply adding BLE or IEEE Std. 802.15.4 connectivity to an existing embedded controller system, or used as a stand-alone smart wireless sensor with embedded application where no host controller is required.
Freescale provides fully certified protocol stacks and application profiles to supportKW40Z. The KW40Z Flash and SRAM memory are available for applications and communication protocols using a choice of Freescale or 3rd party software development tools.
The RF section of the KW40Z SoC is optimized to require very few externalcomponents, achieving the smallest RF footprint possible on a printed circuit board. Extremely long battery life is achieved though efficiency of code execution in the Cortex-M0+ CPU core and the multiple low power operating modes of the KW40Z SoC. Additionally, an integrated DC-DC converter enables a wide operating range from 0.9 V to 4.2 V. The DC-DC in Buck mode enables KW40Z to operate from a single coin cell battery with a significant reduction of peak Rx and Tx current consumption. The DC-DC in boost mode enables a single alkaline battery to be used throughout its entire useful voltage range of 0.9 V to 1.795 V.
KW40Z主要特点:
• Multi-Standard Radio
C 2.4 GHz Bluetooth Low Energy version 4.1compliant
C IEEE Standard 802.15.4 2011 compliant
C Typical Receiver Sensitivity (BLE) = -91 dBm
C Typical Receiver Sensitivity (802.15.4) = -102 dBm
C Programmable Transmitter Output Power: -18 dBmto +5 dBm
C Low external component counts for low costapplication
• MCU and Memories
C Up to 48 MHz ARM® Cortex-M0+ core
C On-chip 160 KB Flash memory
C On-chip 20 KB SRAM
• Low Power Consumption
C Typical Rx Current: 6.5 mA (DCDC in buck mode,3.6 V supply)
C Typical Tx Current: 8.4 mA (DCDC in buck mode,3.6 V supply) for a 0 dBm output
C Low Power Mode (VLLS0) Current: 206 nA
• Clocks
C 32 MHz Crystal Oscillator
C 32 kHz Crystal Oscillator
• System peripherals
C Nine low-power modes to provide poweroptimization based on application requirements
C DCDC Converter supporting Buck, Boost, and
Bypass modes
C DMA Controller
C COP Software watchdog
C SWD Interface and Micro Trace buffer
C Bit Manipulation Engine (BME)
• Human-machine interface
C Touch Sensing Input
C General-purpose input/output
• Analog modules
C 16-bit Analog-to-Digital Converter (ADC)
C 12-bit Digital-to-Analog Converter (DAC)
C 6-bit High Speed Analog Comparator (CMP)
• Timers
C 16-bit low-power timer (LPTMR)
C 3 Timers Modules(TPM): One 4 channels TPM andTwo 2 channels TPMs
C Programmable Interrupt Timer (PIT)
C Real-Time Clock (RTC)
• Communication interfaces
C 2 SPI modules
C 2 I2C modules
C Low Power UART module
C Carrier Modulator Timer (CMT)
• Security
C AES-128 Accelerator (AESA)
C True Random Number Generator (TRNG)
• Operating Characteristics
C DCDC Converter supporting Buck, Boost, andBypass modes
C Temperature range (ambient): -40 to 85°C
Radio features
Operating frequencies:
• 2.4 GHz ISM band (2400-2483.5 MHz)
• MBAN 2360-2400 MHz
Supported standards:
• Bluetooth v4.1 Low Energy compliant 1 Mbps GFSK modulation
• IEEE Std. 802.15.4-2011 compliant O-QPSK modulation
• Freescale Thread Networking Stack
• Bluetooth Low Energy(BLE) Application Profiles
• ZigBee PRO and application profiles
Receiver performance:
• Receive sensitivity of -91 dBm for BLE
• Receive sensitivity of -102 dBm typical for IEEE Std. 802.15.4
Other features:
• Programmable transmit output power from -18 dBm to +5 dBm with DC/DC bypassand buck modes of operation
• Bluetooth Low Energy Link Layer hardware
• Hardware acceleration for IEEE Std. 802.15.4 packet processing
• 32 MHz crystal reference oscillator
• Supports antenna diversity option for IEEE Std. 802.15.4
• Supports dual PAN for IEEE Std. 802.15.4 with hardware-assisted address matchingacceleration
• Differential RF port shared by transmit and receive
• Low external component count
• Supports transceiver range extension using external PA and/or LNA
Microcontroller features
ARM Cortex-M0+ CPU
• Up to 48 MHz CPU
• As compared to Cortex-M0, the Cortex-M0+ uses an optimized 2-stage pipeline
microarchitecture for reduced power consumption and improved architectural
performance (cycles per instruction)
• Supports up to 32 interrupt request sources
• Binary compatible instruction set architecture with the Cortex-M0 core
• Thumb instruction set combines high code density with 32-bit performance
• Serial Wire Debug (SWD) reduces the number of pins required for debugging
• Micro Trace Buffer (MTB) provides lightweight program trace capabilities usingsystem RAM as the destination memory
Nested Vectored Interrupt Controller (NVIC)
• 32 vectored interrupts, 4 programmable priority levels
• Includes a single non-maskable interrupt
Wake-up Interrupt Controller (WIC)
• Supports interrupt handling when system clocking is disabled in low power modes
• Takes over and emulates the NVIC behavior when correctly primed by the NVIC on
entry to very-deep-sleep
• A rudimentary interrupt masking system with no prioritization logic signals forwake-up as soon as a non-masked interrupt is detected
Debug Controller
• Two-wire Serial Wire Debug (SWD) interface
• Hardware breakpoint unit for 2 code addresses
• Hardware watchpoint unit for 2 data items
• Micro Trace Buffer for program tracing
On-Chip Memory
• 160 KB Flash
• Firmware distribution protection. Flash can be marked execute-only on a persector
(4 KB) basis to prevent firmware contents from being read by 3rd parties
• Flash implemented as one 128 KB block and one 32 KB block. Code canexecute or read from one block while the other block is being erased orprogrammed
• 20 KB SRAM
• Security circuitry to prevent unauthorized access to RAM and flash contents through
the debugger
图1{京电港论坛}.KW40Z/KW30Z/KW20Z简化框架图
低功耗蓝牙(BLE)心率监测仪参考方案
The BLE Heart Rate Monitor reference design demonstrates the implementation of a wireless electrocardiogram (ECG) acquisition system. It features the Freescale MKW40 system on chip (SoC) which includes an ARM® CortexTM M0+ processor together with a 2.4 GHz radio for BLE and 802.15.4.
The ECG signal is obtained from the finger tips and processed by the MKW40 SoC. Bluetooth® Low Energy (BLE)心率监测仪参考方案演示了无线心电图(ECG)收罗系统是如何实现的。它接纳KW40Z片上系统(SOC)。该系统包罗一个ARM® Cortex® M0+处理器，并配备了面向BLE和802.15.4的2.4 GHz无线电。
ECG信号从指尖收罗，并通过Kinetis KW40Z SoC处理。然后，盘算用户的心率，并通过BLE传输给智能手机应用。该参考方案可由锂离子纽扣电池供电。由于Kinetis KW40Z MCU的低功耗特点，一个3.6V 200mA/h锂离子可充电纽扣电池可在一连使用的情况下供电长达40小时。恩智浦MC34671用作该器件的电池充电器办理方案。
图2{京电港论坛}.低功耗蓝牙(BLE)心率监测仪参考方案外形实物图
低功耗蓝牙(BLE)心率监测仪参考方案主要特点:
包罗恩智浦超低功耗的Kinetis KW40Z SoC BLE/ZigBee平台。由于该办理方案的低功耗特点，只需接纳一个小小的纽扣电池就能一连运行40小时。
完全符合Bluetooth v4.1 Low Energy
差分输入/输出端口与外部混频变压器联合使用，实现单端口操纵
图3{京电港论坛}.低功耗蓝牙(BLE)心率监测仪参考方案框架图
图4{京电港论坛}.低功耗蓝牙(BLE)心率监测仪参考方案应用框架图
图5{京电港论坛}.低功耗蓝牙(BLE)心率监测仪参考方案软件架构图
图6{京电港论坛}.低功耗蓝牙(BLE)心率监测仪参考方案电路原理图纸(1)
图7{京电港论坛}.低功耗蓝牙(BLE)心率监测仪参考方案电路原理图纸(2)
详情请复制打开此衔接地址:
http://cache.nxp.com/files/32bit/doc/data_sheet/MKW40Z160.pdf?pspll=1
和http://www.nxp.com/webapp/sps/download/preDownload.jsp?render=true
KW40HRMRDUG.pdf
KW40HRMUG.pdf
KW40ZHRTRTQSG.pdf
热点图文