Silabs公司的C8051F85x/86x系列产物是全集成的混淆信号系统级(SoC)MCU,集成了上电重置,电压监督器,看门狗定时器和时钟振荡器,高达8kB闪存,片上调试,12位ADC等,工作电压2.2V-3.6V,可以用在马达控制.本文先容了C8051F85x/86x系列主要特点,框架图,以及BLDC马达参考方案动力板和MCU板主要特点,框架图,电路图以及质料清单.
The C8051F85x/86x device family are fully integrated, mixed-signal system-on-a-chip MCUs. With on-chip power-on reset, voltage supply monitor, watchdog timer, and clock oscillator, the C8051F85x/86x devices are truly standalone system-on-a-chip solutions. The flash memory is reprogrammable in-circuit, providing non-volatile data storage and allowing field upgrades of the firmware. The on-chip debugging interface (C2) allows non-intrusive (uses no on-chip resources), full speed, in-circuit debugging using the production MCU installed in the final application. This debug logic supports inspection and modification of memory and registers, setting breakpoints, single stepping, and run and halt commands. All analog and digital peripherals are fully functional while debugging. Each device is specified for 2.2 to 3.6 V operation, and are available in 20-pin QFN, 16-pin SOIC or 24-pin QSOP packages. All package options are lead-free and RoHS compliant. The device is available in two temperature grades: -40to +85 ℃ or C40to +125 ℃.
C8051F85x/86x主要特点:
图1{京电港论坛}.C8051F85x/86x系列方框架图
C8051F850 BLDC马达参考方案套件
This design kit provides a complete system-level solution for sensorless, brushless dc (BLDC) motors. This application note includes complete schematics, PCB layouts and firmware.
This kit supports 3-phase BLDC motors that meet the following specifications:
Trapezoidal back-EMF
Max operating voltage of between 10 V to 24 V dc
24 kHz PWM frequency
Maximum average current of 10 A
Maximum speed not exceeding 200,000 rpm for a 2-pole BLDC motor
Overcurrent detection capability stops the motor when average current exceeds 10 A.
Motor Stall detect capability stops the motor when a motor stall is detected or extreme loads encountered.
Tachometer Frequency Generator (FG) output signal
The kit aims to demonstrate the capabilities of the C8051F850 for operating BLDC motors. The unique features offered by this MCU for BLDC motor operation are:
PWM synchronized blanking of comparator for BEMF Zero-Crossing Detection
Automatic PWM duty cycle reduction to limit motor current during startup
Hyperdrive mode to increase the maximum speed of some motors
C8051F850 BLDC马达参考方案套件包罗:
One MCU Board: MCRD-MCU-C8051F850 with the motor control firmware preprogrammed into the MCU
One Powertrain Board: MCRD-PWR-NLV-F85X
One BLDC Motor: Turnigy 450 Series 3800 kV Brushless Outrunner Helicopter Motor
One Motor Mount Board
One 8-bit MCU Kit CD
One 12 V, 5 Amp Universal Input Power Adapter
图2{京电港论坛}.C8051F850 BLDC马达参考方案框架图
1.动力板
The powertrain board is designed to meet the following key motor specifications:
Motor supply voltage range of 10 to 24 V
Maximum average current of 10 amps
It consists of the following components that are relevant to this application:
6 IRFH7446 Power MOSFETS for the inverter circuit
3 Silicon Labs Si8230 isolated dual drivers
An LDO to generate the 3.3 V required by the MCU board
50 m current sensing resistor rated for 10 W
Motor terminal blocks to allow user to attach their own motor
Resistor divider to generate attenuated motor voltage supply (VMDC) - allows MCU to determine if motor supply voltage is high enough for safe operation
Resistor dividers to generate attenuated motor phase voltages with a small positive offset voltage (VMA,VMB, VMC)
Resistor network to generate attenuated sum of motor phase voltages with a small positive offset voltage(VMY)
2.MCU板
The MCU board consists of the following:
C8051F850-A-GU QSOP-24 package
2 push-buttons
3 controllable LEDs
1 rotary variable resistance potentiometer
Op-amp to amplify and bias the current sense voltage
USB Hub to support:
C2 USB debug interface
CP2103 USB-UART bridge operating at 115200 baud
CP2112 USB-I2C bridge
Configurable jumpers to select either Hall-sensored or sensorless mode of operation
Test points for connecting to gate drive of user powertrain board and motor.
图3{京电港论坛}.C8051F850 BLDC马达参考方案外形图
图4{京电港论坛}.C8051F850 BLDC马达参考方案电路图:动力板(1)
图5{京电港论坛}.C8051F850 BLDC马达参考方案电路图:动力板(2)
图6{京电港论坛}.C8051F850 BLDC马达参考方案电路图:动力板(3)
图7{京电港论坛}.C8051F850 BLDC马达参考方案电路图:MCU板
图8{京电港论坛}.C8051F850 BLDC马达参考方案电路图:运放
图9{京电港论坛}.C8051F850 BLDC马达参考方案电路图:USB桥
图1{京电港论坛}0.C8051F850 BLDC马达参考方案电路图:USB Hub
图1{京电港论坛}1.C8051F850 BLDC马达参考方案电路图:毗连器
图1{京电港论坛}2.C8051F850 BLDC马达参考方案电路图:低本钱BLDC马达设计样板
C8051F850 BLDC马达参考方案动力板质料清单:
C8051F850 BLDC马达参考方案MCU板质料清单:
详情请复制打开此衔接地址:
http://www.silabs.com/Support%20Documents/TechnicalDocs/C8051F85x-86x.pdf
和http://www.silabs.com/Support%20Documents/TechnicalDocs/AN794.pdf
AN794.pdf
C8051F85x-86x.pdf
热点图文